NOTICE: Most tools are extremely difficult to find since these were provided only
to the dealers to purchase.
Because of this, some tools can only be obtained from old dealer service departments.
Most tools were discontinued being made by the manufacturers.
A
B
A -
#0658-001-000 -
$16
Sachs Clutch hub
tool for stacking up clutch plates
B - #99-30-17812
- $4
Sachs selector rod
tool for removing selector keys
fits 1/2” drive
socket tool
#0276-150-005 -
$27
Magneto puller
for Bosch and
Motoplat external flywheels
26mm medium threads
external Motoplat flywheel shown in photo
#0276-150-100 - $27
Magneto puller for
Motoplat internal flywheels
27mm fine threads
internal Motoplat flywheel shown in photo
Sachs Shift Adjustment Tool
a vital tool for holding shifter shaft steady during adjustment
of the transmission
10mm cap protects mag nut threads from getting mushed
for use with crank bearing puller on Sachs 100 & 125 engines
#0276-156-000 - $7 ea
13mm cap protects mainshaft end from getting split
when using puller to remove sprockets
#0676-012-200 - Sold out
20mm O.D. x 10mm O.D. x 7.6mm I.D. x 9mm tall
#0276-160-001 - $2 ea
#0276-065-101 - Sold out
wrist pin extractor
A
B
C
D
Inserts fit onto end of extractor to fit wrist pin diameter
A #0276-122-011 - 11.8mm O.D. - sold out
B #0276-122-013 - 13.8mm O.D. - $11 ea
for 100/ 125/ 175 piston wrist pins
C #0276-122-017 - 17.8mm O.D. - $11 ea
for 250/ 400/ 420/ 495 piston wrist pins
D #0276-122-021 - 21.2mm O.D. - $11 ea
Inserts through piston to line piston up on rod prior to inserting
the wrist pin, 2" long - slightly smaller diam. for easy insertion.
#0977-053-000 - $2 ea
#2876-007-000 - $3 ea
Twin flat blade screw driver - small & tiny blades
great for Bosch and Motoplat timing adjustements
A
B
A- #0676-027-000 -
$10 ea
extractor for brass wrist pin
bushing in alloy rods
B- #0276-135-000 -
Sold out
timing gauge for ignition advance on
Bosch and Motoplat
#1476-011-000 - sold out
A
B
C
D
Jaws for Bearing Puller
split jaws fit over puller #1476-011-000 and bearing
and are locked in place with clamp ring
Bearing end has thin lip to grab outer bearing edge
A #JAWS-33 - fits NJ205 bearings Sold out
B #JAWS-36 - fits NJ305 bearings Sold out
C #JAWS-39 - fits NJ206 bearings Sold out
D #1437-009-000 - clamping ring, 58mm I.D. Sold out
A
B
C
Jaws for Bearing Puller
split jaws fit over puller #1476-011-000 and bearing
and are locked in place with clamp ring
Bearing end has thick lip
A #JAWS-41 - approx 41mm I.D. pull Sold out
B #JAWS-35 - approx 35mm I.D. pull $20 ea
C #1437-009-000 - clamping ring, 58mm I.D. Sold out
A
B
C
D
large size Jaws for Bearing Puller
split jaws fit over puller #1476-011-000 and bearing
and are locked in place with clamp ring
Bearing end has thick lip
A #JAWS-60 - approx 60mm I.D. with clamp ring $30 ea
B #JAWS-48 - approx 48mm I.D. pull $20 ea
C #JAWS-57 - approx 57mm I.D. pull $20 ea
D #1447-010-000 - clamping ring, 75mm I.D. $40 ea
for #JAWS-48 & #JAWS-57
Bearing puller with assorted selection of 16 jaws
includes 3 clamping rings 58mm / 75mm / & 85mm
includes jaws for E15/ BO17/ & M25 crank bearings
#1476-011-KIT - bearing puller kit. sold out
used to pull inner race from crank pin - $80 only 1 in stock
A
B
A-
#0276-121-001 - sold
out
holding plate for pinion gear
on 80cc Sachs
B- #0676-109-000 - sold
out
holding plate for pinion gear on
100cc & 125cc
Sachs engines
#0276-019-101 - Sold out
spacer plate
#0277-086-406 - sold out
Hook spanner with 420 & 428 chains
for use on Sachs 80, 100, 125 engines
A
B
A-
#99-30-206 - sold
out
Layshaft Bearing Puller for all
sachs motors
B-
#0277-100-000 -
$30
Shift Adjustment tool for Sachs
motors
holds shifter shaft steady made in USA
A
B
Jig for Aluminum Rod Bushing
A- #0276-157-000 - sold
out
holding jig for reamer
B-
#0276-159-002 -
sold
out
bronze bushing reamer for wrist pin
complete 5 piece engine stand mounted on thick wood base
allows engine to be swiveled and tilted
sold out